**I thought I pretty well knew everything about dividing a number by two. I was about to hit the publish button, but I reckoned I should first do a quick scan of the web. Again,**

*Holy Moly!*

*holy moly !!*This post was initiated by my watching a very skillful carpenter reface our fifteen year old kitchen cabinets. He was a "measure twice, cut once" sort of guy. In the course of his work, he did a lot of marking and checking of centre lines so that handles and panels could be precisely located.

Locating a centre line comes down to finding the midpoint of a measured length, in other words, dividing a number by 2. How he did this might surprise you, as did the advice I encountered on the web.

The measurements to be halved are usually mixed numbers. I happen to have a board that is 9

^{7}⁄

_{8 }inches wide, and I asked my wife (who is not a mathematician) how she would find the centre line. This is how she explained it using her usual yardstick (which has a resolution of one-eighth of an inch and which dictated her approach).

The midpoint would be half of 9^{7}⁄_{8}.

Half of 9^{7}⁄_{8}is half of 9 plus half of^{7}⁄_{8}, which is 4^{1}⁄_{2}inches plus 3^{1}⁄_{2}eighths.

So measure 4^{1}⁄_{2}inches and tack on an extra 3^{1}⁄_{2}eighths to get the midpoint:

^{7}⁄

_{16}inches beyond the 4

^{1}⁄

_{2}inch mark (rather than 3

^{1}⁄

_{2}eighth-inches).

There is another way which comes to mind: 9

^{7}⁄

_{8}is the same as 10 −

^{1}⁄

_{8}, so half of 9

^{7}⁄

_{8}is the same as half of 10 minus half of

^{1}⁄

_{8}, which is 5 −

^{1}⁄

_{16}, in which case you would probably find the midpoint by locating the 5 inch mark and backing up

^{1}⁄

_{16 }inch. I would have used this way myself, and I suspect some carpenters would do it this way as well.

###
**What did the web say?**

On the web almost every "explanation" of how to divide a mixed number by a whole number reduced the problem to dividing two fractions using

*the invert-and-multiply trick*. According to these posts, dividing 9

^{7}⁄

_{8}by 2 should be done as follows:

- Convert the mixed number to an improper fraction: 9
^{7}⁄_{8}=^{79}⁄_{8}. - Convert the 2 to an improper fraction: 2 =
^{2}⁄_{1}. - Do the division
^{79}⁄_{8}÷^{2}⁄_{1}. (by which they meant:^{79}⁄_{8}÷^{2}⁄_{1}=^{79}⁄_{8}×^{1}⁄_{2}= . . . ). - Convert back to a mixed number:
^{79}⁄_{16}= 4^{15}⁄_{16}.

By the way, my wife said she never really understood the

What is somewhat astonishing is that I found two sites that described an algorithm designed precisely to solve our very specific problem, namely, *invert-and-multiply*thing. She said she would change the two fractions so that they had a common denominator and then divide the top numerator by the bottom one. For example, to find^{2}⁄_{3 }divided by^{3}⁄_{5 }she would reason as follows:^{2}⁄_{3 }divided by^{3 }⁄_{5 }is the same as^{10}⁄_{15 }divided by^{9}⁄_{15 }, which is the same as 10 divided by 9, or^{10}⁄_{9 }.

**how to divide a mixed number by 2**. The algorithm differed according to whether the whole part of the mixed number was even or odd.

Here is how it applied to dividing 9

^{7}⁄

_{8}by 2:

- Divide the whole part of the mixed number into half (ignore the remainder): 9 ÷ 2 ➞
**4.** - Add the numerator and denominator of the fraction: 7 + 8 =
**15**. - Double the denominator of the fraction: 2 x 8 =
**16**. - The answer is 4
^{15}⁄_{16}

Most of the web stuff mentioned above never really explained why the particular algorithm worked. And I did not encounter any post on the web that used the distributive law to divide a mixed number by a whole number, that is, no-one suggested doing what my wife and I did:

### Which method did the cabinet installer use?

**Answer:**None of the above.

Instead, he used a

**self-centering tape measure.**This is a tape measure that has two number lines on it. The top one in black shows standard feet and inches, and the other one directly below it in red shows the half measurements. Here is the board being measured by a self-centering tape:

^{7}⁄

_{8}inches and that centre line of the board is at the 4

^{15}⁄

_{16 }inch mark. The point on the centre line can then be immediately marked on the board without actually doing any computations.

* * * * *

As I was rewriting this post, I encountered a couple of tweets by

**John Golden**(@mathhombre) and

**Denise Gaskins**(@letsplaymath) that directed me to their posts* about Richard Skemp's work which seemed to be relevant to what's going on here. (Thanks.)

Skemp observed that people lean in one of two opposite directions when they describe what it means to "understand" mathematics. He called the one way an

*instrumental*understanding, and the other, a

*relational*understanding. (A detailed summary can be found in the posts mentioned below.) He contended that the way you tilt affects both how you learn math and how you think it should be taught. A person with an instrumental viewpoint would tend to think of math and teach it as a collection of rules to be memorized and applied. A person with a relational viewpoint would likely think of and teach math as exploring the connections between various parts of the subject.

If I grasp Skemp correctly, the stuff from the web that I mentioned above falls very much to the instrumental side while the approach that uses the distributive law is more relational.

The carpenter’s use of a self-centering tape would also appear to reflect an instrumental view of mathematics. But not necessarily—it could simply be a tradesman using a tool that simultaneously decreases the chances of making errors and increases the speed of doing the work.

* * * * *